Hardness – volumetric characteristic of material
DOI:
https://doi.org/10.31548/machenergy2021.04.139Keywords:
performance, mechanical properties, hardness, micro-hardness, volumetric hardness, indentor, penetration depth, displaced metal volumeAbstract
Producing details for different purposes is guided by the conditions of their work and, therefore, attention is paid to such characteristics as strength, viscosity and hardness. Only the method of determining the hardness of the material allows you to conduct research without destroying the detail in addition to physical methods. This takes into account the fact that the other properties are indirectly related to the hardness parameter. The main disadvantage of all modern methods of the material hardness measurement is the inconsistency of the practical content of the units of measurement of the studied parameter to the theoretical essence of hardness - as a physical quantity that characterizes the properties of a rigid body. The units of all hardness measurement methods, depending on the scale factor, are usually compared by converting their values to such generally accepted methods as Brinell, Rockwell, or Vickers. The conversion of the hardness values obtained by different methods should be used very carefully and preferably for a preliminary assessment of the relative changes in material properties. When applying these methods, the units of measurement are the ratio between the load on the indenter, a given standardized shape and the area or depth of the imprint. However, based on the physical content of a property such as hardness, it is necessary to determine the relationship between the load on the indenter and the volume of the displaced material. This work aims to establish a theoretical basis for the digital characteristics of units of hardness obtained by different measurement methods. To provide the physical meaning of the determining of hardness, the dependence of the volume of the displaced material on the applied load was determined. The comparison of these values made it possible to really determine the relationship between the units of different methods not based on practical comparisons, but by summing up the theoretical basis. The obtained results indicate a sufficiently high correlation between the results obtained with different hardness measurement methods.
References
Vilys J., Ciuplys К, Terentjev К, Kolmakov А. et al. (2003). Particularies of Plastic Deformation of Metals Near Surface Layers. Kaunas. Technologija. 208.
Nazarenko I., Mishchuk Y., Mishchuk D., Ruchynskyi M., Rogovskii I., Mikhailova L., Titova L., Berezovyi M., Shatrov R. (2021). Determiantion of energy characteristics of material destruction in the crushing chamber of the vibration crusher. Eastern-European Journal of Enterprise Technologies. 4(7(112). 41-49. https://doi.org/10.15587/1729-4061.2021.239292.
DSTU EN 6506-1: 2007 Metallic materials. Determination of Brinell hardness. Part 1. Test method.
DSTU EN 6506-4: 2008 Metallic materials. Determination of Brinell hardness. Part 4. Table of hardness values.
DSTU EN 6507-1: 2007 Metallic materials. Determination of Vickers hardness. Part 1. Test method.
DSTU EN 6508-1: 2013 Metallic materials. Determination of Rockwell hardness. Part 1. Test method (scales A, B, C, D, E, F, G, H, K, N, T).
Titova L. L. (2020). Criteria for evaluation of efficiency of using machines in agricultural complex. Machinery & Energetics. Journal of Rural Production Research. Kyiv. Ukraine. 11(2). 151-156. ISSN 2663-1334 (print), ISSN 2663-1342 (online), www.journals.nubip.edu.ua/index.php/Tekhnica. DOI: 10.31548/machenergy.2020.02.151-156.
Nazarenko I., Dedov O., Bernyk I., Rogovskii I., Bondarenko A., Zapryvoda A., Titova L. (2020). Study of stability of modes and parameters of motion of vibrating machines for technological purpose. Eastern-European Journal of Enterprise Technologies. 6 (7-108). 71-79. doi: 10.15587/1729-4061.2020.217747.
Student M., Gvozdetsky V., Student O., Prentkovskis O., Maruschak P., Olenyuk O., Titova L. (2019). The Effect of Increasing the Air Flow Pressure on the Properties of Coatings during the Arc Spraying of Cored Wires. Strojnicky Casopis. 69(4). 1 December. 133-146.
Rogovskii I. L, Titova L .L., Remshev E. Yu., Solomka O. V., Voinash S. A., Malikov V. N.,
Olekhver A. I. (2021). Research of sliding bearings with reverse friction pair and inlaid liners made of thermoplastic composite materials. Journal of Physics: Conference Series. 1889. 042010. doi:10.1088/1742-6596/1889/4/042010.
Titova L. L. (2021). Modeling of transients of dynamic model of power power plant of machines for forestry works. Machinery & Energetics. Journal of Rural Production Research. Kyiv. Ukraine. 12(1). 147-154.
Titova L. L. (2021). Methods of finding the optimal parameters of production processes with variable composition of machines for forestry work. Machinery & Energetics. Journal of Rural Production Research. Kyiv. Ukraine. 12(2). 97-104.
Titova L. L. (2021). Mathematical model of optimization of parameters of production processes of machines for forestry works. Machinery & Energetics. Journal of Rural Production Research. Kyiv. Ukraine. 12(3). 77-85.
Downloads
Published
Issue
Section
License
Relationship between right holders and users shall be governed by the terms of the license Creative Commons Attribution – non-commercial – Distribution On Same Conditions 4.0 international (CC BY-NC-SA 4.0):https://creativecommons.org/licenses/by-nc-sa/4.0/deed.uk
Authors who publish with this journal agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).
