RESEARCH AND EVALUATION OF LACQUER COATING HARDNESS APPLIED TO ARTIFICIALLY AGED WOOD SAMPLES



N. V. Buiskikh, D. V. Morokova

Анотація


The hardness  of  lacquer coating  is one of the most important physical and mechanical features , which gives the ideas of  its cohesion strength,  degree of its drying and possibility of use of the product under variable  conditions. Insufficient hardness leads to a  loss of protective and decorative coating functions in the process of products use. The research of  lacquer  coating hardness are conducted  on softwood samples. It shows that  nature of  the  substrate significantly affects the strength of lacquered surface and determines specificity of coating hardness. Heterogeneity of softwood structure  and lower hardness of early annual layers of wood  affect   quality of  coating negatively.

The issue of coating hardness has been researched by Professor V. G. Sanaev (Moscow State Forest University).  He  developed a method of control which depends on the depth of penetration of spherical indention and suggested standards of  hardness for protective  and decorative coatings. To create a better modern market for furniture new special effects  such as brushing are used . The idea of this technique  is to remove the  outer  layer of wood with a special soft brush, which enables to  create a surface with pronounced structure of annual rings. But as a result the wood surface is disturbed and vulnerable to all kinds of damage such as decay, pollution and mechanical damage.  Application of lacquer coating of higher hardness can protect this kind of surface. That is why the research of coating hardness is an important issue in order to extend the product’s life.

The objective of the research is to determine the effectiveness of commercially available brands of lacquer coatings, applied to artificially aged samples. The experimental and statistical methods of research were applied for this purpose.

Material and methods. The samples were made of pinewood board with humidity level 10-12%. The brushing was done by “Makita” company. A total of three groups consisting of 10 samples were provided. Various brands of lacquer were applied. One group of samples was a control group. All samples were sprayed with stain-primer  and patina.  The samples of the first group  were coated with Osmo brand oil-wax product. The second group of the samples were coated with water-dispersion lacquer of  Kompozit brand. The samples of the third group were treated with yacht lacquer of Alpina brand. The samples of the fourth group were represented by unbrushed samples, coated with patina and water-dispersion lacquer of Kompozit brand. Uncoated samples of brushed pinewood board were assigned as a control group. Hardness testing machine “Novotest” was used to determine the surface hardness of lacquer coatings. The device met the standards DIN 53505, ASTMD2240 [5], ISOR868, JISR 7215. 

Research results. Methods of mathematical statistics were applied for data processing. Figure 3 showed a comparative analysis of tested samples hardness. Coefficient V = 24 – 28% was significantly high. This could not be explained by the fact that lacquer film of brushed surface did not  have a homogeneous structure. The surface sagged more in early stage of annual growth rings because it had a lower hardness than in the late stage.

The maximum surface hardness, which was 0,59 HD was observed in samples, coated with yacht lacquer. The surface hardness  of  the group of samples coated with water-dispersion lacquer was less 7% compared to the above mentioned one. The lowest surface hardness  less 27 % was obtained in a group of  oil-waxed samples.

         Research conclusions. Despite the fact that lacquer coating did not provide a solid film on brushed  surfaces,  even  less hardness was determined for uncoated samples. This proved the  importance and necessity of brushed surfaces  protection with lacquer.


Повний текст:

PDF (English)

Посилання


Брацук В. В. Повышение твердости лакированных поверхностей изделий из древесины хвойных пород : автореф. дис. на соискание учен. степени канд. техн. наук : 05.21.05 / Виталий Владимирович Брацук. – Красноярск : 2002. – 23 с.

Санаев В. Г. Методы определения твердости защитно-декоративных покрытий на древесине / В. Г. Санаев // Деревообрабатывающая промыленность. –1990. –№ 10. – С.31–33.

Твердомір Novotest TШ-Ц [Електронний ресурс]. – Режим доступу:

http://novotest.ua/tverdomery/tverdomer-reziny-po-shoru-tsh-ts-tsifrovoy.

Шмит Я. Т. ?сследование особенностей отделки древесины лиственницы и механических свойств образованных на ней отделочных покрытий : автореф. дис. на соискание учен. степени канд. техн. наук : 05.21.05 // Янис Тадеус Шмит. – Рига : 1975. – 32 с.

DIN 53505, ASTM D2240 [Електронний ресурс]. – Режим доступу:

www.techstreet.com/ASTM+D2240‎

ISO R868, JIS R 7215 [Електронний ресурс]. – Режим доступу:

www.slideshare.net/.../hardness-tester-for-plasti


Метрики статей

Завантаження метрик ...

Metrics powered by PLOS ALM

Посилання

  • Поки немає зовнішніх посилань.